Alumina ceramic sleeve lined pipe and elbow

The Alumina ceramic sleeve lined pipe and elbow a smooth inner wall, excellent tightness as well as good wear and chemical resistance ability.

Alumina ceramic sleeve lined straight pipe
Alumina ceramic sleeve lined straight pipe
Alumina ceramic sleeve lined pipe bend
Alumina ceramic sleeve lined pipe bend
Alumina ceramic sleeve lined pipe elbow
Alumina ceramic sleeve lined pipe elbow

For the convenience of customers, are to provide a more specific process is as follows:

  1. Removing rust and decontamination process of outer-layer steel pipe;
  2. Must be in strict accordance with the prescribed ratio, the binder a\b accurate measurement, with how many, must be stirred evenly, full stir-mixing must not be less than 4 times, such as adding a mixture of the embedded feed should be mixed with the binder and then add the mixture to stir up not less than 3 times;
  3. The binder is applied evenly on the inner wall of the steel tube to ensure the thickness is not less than 0.5mm thickness. Then apply the binder on the outer surface of the ceramic ring to ensure the thickness between the 0.5mm-1mm. Also in the ceramic ring side (with the ceramic ring contact with the corresponding surface) Daub 0.5mm Adhesive, to ensure that after the installation of the ring and the seal between the ring;
  4. After the installation of the ceramic ring in place, it is necessary to repair the gap between the assembled ceramic rings and mend the joints to ensure the sealing between the ring and the ring;
  5. According to the NPT standard, we process the two pipe ends of male and female thread processing. The end of the pipe processing, and processing 1×45° groove, to prevent on-site installation in the process of cutting the hands of construction workers, do a good job of safety protection measures, thread processing, need to brush oil to protect the thread;
  6. After installing the ceramic ring, check the internal surface of the ceramic ring of the formation, finishing in place, cannot move the position of the pipe, because the binder is not dry, vibration is easily caused by the displacement of ceramic rings, affect the use of the effect of cold weather in winter, binder drying time is longer, need to ensure more than 48 hours.

Relevant technical introduction of wear-resistant ceramic ring
The wear resistant ceramic ring is a special kind of ceramic with Al2O3 as the main raw material and the rare metal oxide as the flux, which is melted by high temperature at 1700 oC.

99.7% Alumina ceramic tube/high frequency ceramic is our main product. We are making High quality alumina furnace tubes.

99.7% alumina is the main material, 85% and 95% alumina tubes also available.



  1. The wear-resistant ceramic ring has the characteristics of smooth interior wall and super wear resistance. Widely used in chemical, fine powder conveying pipelines and other industries, with high wear-resistant and anti-corrosion functions.
  2. In accordance with the traditional process, the production of wear-resistant ceramic ring is mainly the use of hot-pressing casting or grouting molding. Adopting isostatic pressing forming technology, the ceramic ring with isostatic pressing is better in compactness and more accurate in ceramic size.
  3. At present, our ceramic ring lining pipeline in the silicone industry, chemical industry, fine powder conveying industry has been widely used.
Technical index of wear-resistant ceramic ring:
Item Data Note
Al2O3 (%) ≥95%
Density (g/cm3) ≥3.65g/cm3
Strength (MPa) 1030
Flexural strength (MPa) 212
Impact toughness (Kj/m2) 10.2
Hardness (HRV) ≥85Mpa
Elastic modulus (GPa) 304
Expansion coefficient (10-6/℃) 6.6
Acid resistance(24H) Stability Test solution :
Alkali resistance(24H) Stability Test solution:

Technical index of binder:

Technical index of binder:
Item Data Characteristics of binder
Density (g/cm3) 1.32
We use the Australian Megapoxy high strength structural adhesive, this structural glue is modified epoxy resin polymer, anti-aging ability, and wear-resistant ceramic bonding to form a strong and cushion of the anti-wear layer, cured water, anti-corrosion performance is excellent, toughness, displacement-resistant effect is remarkable.

Megapoxy binder

Compressive strength (MPa) 40
Shear Strength MPa 26
Impact toughness Kj/m2 10
Hardness HB 9.5
Elastic Modulus GPa 2.2
Expansion coefficient 10-6/℃ 20.1
Softening temperature℃ 263
Coking temperature℃ 335
Acid resistance(24H) Stability Test solution :
Alkali resistance(24H) Stability Test solution:


电子邮件地址不会被公开。 必填项已用*标注