Ceramic sleeve lined Pipe

The tube or sleeve sintered as a whole part, and then assemble it into the steel pipe with our high-strength-temperature-resistant epoxy adhesive.

The has a smooth inner wall, excellent tightness as well as good wear and chemical resistance ability.

The ceramic sleeve lined pipe has a smooth inner wall, excellent tightness as well as good wear and chemical resistance ability.

Alumina ceramic sleeve lined pipe with flange
sleeve lined pipe with flange

Ceramic sleeve lined pipe with flange
Ceramic sleeve lined pipe with flange

Ceramic sleeve lined reducer
Ceramic sleeve lined reducer

Alumina ceramic sleeves lined pipe
Alumina ceramic sleeves lined pipe

Alumina ceramic sleeve lined pipe export to australia
export to australia

95% , elbows and T pipes have been largely applied in lithium battery material conveying system in recently years.

Wear stainless ceramic pipes with below advantages:

  1. Better purity for inside and outside pipe materials;
  2. More abrasive;
  3. Higher resistance;
  4. Stronger impacting resistance;
  5. Better high temperature resistance
  6. Smaller flatness of inside pipe(ceramic flatness≤0.5mm)

In addition, the flatness of ceramic casing is also an important factor affecting the size of lithium battery materials.We did a lot of analysis and improved our manufacturing techniques to solve both of these problems.Now it can help lithium battery delivery systems better solve these problems, with better material purity, longer service life and better economic benefits.

For the convenience of customers, are to provide a more specific process is as follows:
  1. Removing rust and decontamination process of outer-layer steel pipe;
  2. Must be in strict accordance with the prescribed ratio, the binder a\b accurate measurement, with how many, must be stirred evenly, full stir-mixing must not be less than 4 times, such as adding a mixture of the embedded feed should be mixed with the binder and then add the mixture to stir up not less than 3 times;
  3. The binder is applied evenly on the inner wall of the steel tube to ensure the thickness is not less than 0.5mm thickness. Then apply the binder on the outer surface of the ceramic ring to ensure the thickness between the 0.5mm-1mm. Also in the ceramic ring side (with the ceramic ring contact with the corresponding surface) Daub 0.5mm Adhesive, to ensure that after the installation of the ring and the seal between the ring;
  4. After the installation of the ceramic ring in place, it is necessary to repair the gap between the assembled ceramic rings and mend the joints to ensure the sealing between the ring and the ring;
  5. According to the NPT standard, we process the two pipe ends of male and female thread processing. The end of the pipe processing, and processing 1×45° groove, to prevent on-site installation in the process of cutting the hands of construction workers, do a good job of safety protection measures, thread processing, need to brush oil to protect the thread;
  6. After installing the ceramic ring, check the internal surface of the ceramic ring of the formation, finishing in place, cannot move the position of the pipe, because the binder is not dry, vibration is easily caused by the displacement of ceramic rings, affect the use of the effect of cold weather in winter, binder drying time is longer, need to ensure more than 48 hours.
Relevant technical introduction of wear-resistant ceramic ring

The wear resistant ceramic ring is a special kind of ceramic with Al2O3 as the main raw material and the rare metal oxide as the flux, which is melted by high temperature at 1700 oC.

Ceramic lined inner details

Ceramic lined inner details

Ceramic lined inner details

99.7% Alumina ceramic tube/high frequency ceramic is our main product. We are making High quality alumina furnace tubes.

99.7% alumina is the main material, 85% and 95% alumina tubes also available.

Features:
  1. The wear-resistant ceramic ring has the characteristics of smooth interior wall and super wear resistance. Widely used in chemical, fine powder conveying pipelines and other industries, with high wear-resistant and anti-corrosion functions.
  2. In accordance with the traditional process, the production of wear-resistant ceramic ring is mainly the use of hot-pressing casting or grouting molding. Adopting isostatic pressing forming technology, the ceramic ring with isostatic pressing is better in compactness and more accurate in ceramic size.
  3. At present, our ceramic ring lining pipeline in the silicone industry, chemical industry, fine powder conveying industry has been widely used.
Related products maybe you like
Alumina ceramic sleeve lined pipe and elbow
Alumina ceramic sleeve lined pipe
Abrasion&wear resistant alumina ceramic sleeve lined pipe
Wear impact abrasion protection alumina ceramic sleeve lined pipe
Ceramic sleeve lined Pipe

Leave a Reply

Your email address will not be published. Required fields are marked *